6600-724, 6600-286, 6600-044 Circuit Board with Circulation Pump: Sundance® Spas, Jacuzzi® Spas

Replaces: 3-70-0348, 6600-226, 6600-085, 6600-086 and 6600-208, 6600-286

This board is for circulation pump systems (see 6000-125 for reference). Comes with a REV. 3.61 chip. If your circuit board has a Software Chip that begins with a 3, then this is the correct series board. Sundance® Spas has revised this chip several times, we send you the board with the current chip. If you have an older board without a Circulation pump or your board has a chip that begins with a 5, then you need a board with a Series Chip that starts with a 5. which would be the 6600-289 or other.

Sundance® Spas used the same board on different series but sometimes would change the eprom on the board to function on a different system, but not the part number on the board. So the part number on the board may be incorrect. Essential in getting the correct board is to look at the eprom. This is a small 1/4 inch by 1 inch (approx) on the board itself with a white sticker that started with REV. See info below in making the correct choice, if unsure then send a picture of the board with the eprom number visible. Also if your year and model is not listed below it is probably not for your spa. If you have the wrong eprom you can order the correct one on our site.
Note: 6600-722, 6600-724, 6600-042, 6600-044, 6600-289, 6600-286 are the same boards with different eproms on them.

Used on Sundance® Spas:

• 2008-03/2017 780 Dover (1 pump) equipped with a circulation pump
  

• 2007+ 780 1-Pump Metro and Solo equipped with a circulation pump
  

• 2005-2006+ 780/850E 1-pump. Lagunas, Caprio, Metro, Solo equipped with a circulation pump
  

• 2004 Portofino Series 2-Speed Caprio, Metro and Solo equipped with a circulation pump
  

• 2002-2003 Caprio, Caprio ST, Tango and Solo equipped with a circulation pump
  

• 2003-2005 Sweetwater 2-Speed (Lagunas) equipped with a circulation pump
  

• 06/00-2001 Portofino 1-Speed/2-Speed Board (Caprio, Caprio ST, Tango, and Solo). Was 6600-085 equipped with a circulation pump
  

Used on Jacuzzi® Spas:

• 2002+ Jacuzzi® Spas J-300 Series LED Circuit Board

• 2002-2006 J-310, J-315 Series

• 2004 J-325 Series

• 2007+ J-315 Series

• 2008+ J-325 Series

• As of 2007 the J-300 Series are all LED models

6600-724 replaces older 6600-286, 6600-044, 6600-084, 6600-085 and 6600-086 Boards. We will send the latest Board and Eprom Revision

The Circuit Board must have the jumpers configured on the board to the settings on your spa, also the programming for your spa needs to be done. See the links below for the wiring schematic with jumper settings and programming instructions:

• Jumper 1-2: With Jumper on: 15 Amp (if system is 120 Volt only). 30Amp (if system is a 4 wire 120/240 Volt system) 40Amp (if system is a 4 wire 120/240 Volt system)

• Jumper 3-4: With Jumper on: 2 jet pumps (do not confuse the small Circ pump as 1 pump). Without Jumper: 1 Jet pump

• Jumper 7-8: With Jumper on: Centigrade. With Jumper off : Fahrenheit Read out on panel.